Stepper Drivers and Ball Mice

A4983 Carrier
Stepper Driver

Here's one of my new stepper controllers. They can't put more than 0.5A into my 1.68 ohm motors from the 12v supply without overheating, probably due to current squared losses in the chips' fets. I will have to try a lower voltage. The white stuff is some heatsink compound- I was trying to heatsink the chip with little success. I will try something with a clip that goes under the board to hold it steady.

Quadrature Wheel
Ball Mouse Belly
Buffer
Being Used as Input

I'm using a gutted ball mouse as an input device. I'm picking the quadrature signals directly off the photodiodes, so they need some buffering. Quadrature translates perfectly to step/dir, so this allows precise bidirectional control of my stepper. With the A4983 set to 16x microstepping, I have 3200 steps per rev and therefore a wicked reduction ratio from the mouses' wheel. I'm re-splining my stepper shaft because the other splines weren't close enough to the motor body, and I already had this rig set up to test the drivers with. The arduino is in this circuit for two reasons: 1) to count pulses and tell me where I'm up to, and 2) to debounce the pulses, and provide them at a steady rate to my stepper controller to avoid missed steps and noise getting into it.

Overview
Re-Splined Shaft

Bearing Blocks and Print Settings

Y Bearing
360 Inner

Here's my first bearing block, two Y 360 inners put together until I can make matching outers for them. Since the angled bearings aren't perfectly straight and don't align perfectly, it has a tendency to spiral around the rod while travelling, about a quarter turn per 300mm of travel. I think I can clamp against this and overcome the friction until I can print new ones.

These blocks were quite fun to make from wood- lots of work with a bevel gauge, a saw and a wickedly sharp chisel. The holes were eyeballed and drilled out with a cordless drill, since I've had much better luck with this method than the pedestal drill, especially with odd angles.

Print Settings

For those of you having trouble getting prints to scale, the above shows the settings I use in gimp. Other image editors should sport similar settings.

More Prints

Extruder Block
X 360 Z Bearing Plate
X Vert Drive Side Plates

Cutting splines into motor shaft for the extruder, and a start on Y bearing holders

Overview
Cut Splines
Dremel Raised
Cut Splines Close-Up

Here I am cutting splines into a motor shaft in preparation for my extruder according to Pinch-Wheel Variations on reprap wiki.

Motor Controller
L293D Close-Up
7 Ohms of Toaster Nichrome

I'm using my 7 ohms of nichrome to limit current to my stepper, since I don't have a chopper yet, and a 12v/20w dichroic globe to load the PSU's 5v line.

Y Bearing
360 Inner

"Y Bearing 360 Inner", although I haven't yet cut the bearing slots in the bottom yet. They'll have to wait for another day.

More Prints

Y Bearing 180
Y Bearing 360 Inner
Y Bearing 360 Outer

As you can see, I'm trying wireframe instead of translucent, until someone shows me how to render nice engineering drawings in blender with minimal work. Just turning off the wires between coplanar faces would be a start.

I'm slowly developing a picasa upload shell script which spits out thumbnail links, makes things immensely easier!

Z Bar Top Clamps and Z Idler Bracket

Hardwood Z Bar Top Clamp
Clamped onto Bar

Here's the close-ups of the hardwood Z top clamps. I drilled all the holes first then just cut down the middle with my hacksaw, so the two pieces are only a blade-width apart, and the cross-holes have perfect alignment. These new clamps feel very strong and I'm confident they'll survive much better than the last set.

Z Idler Bracket
Test Fit with some bearings mounted

Here's my latest part in-situ, the z idler bracket. It looks like this wood may be a bit soft, but we'll see how it goes. Maybe the washers will just dig in nicely?

Can also see the last of the studding cut to size in the last pic above. Those 418mm lengths through the Z Leadscrew Bases look a bit short to me, maybe make yours 430mm or so unless that's just some sort of error on my part.

Z Motor Bracket, Test Fit

Test Fit
Y Motor Bracket

Here's a test fit of all the parts I've made so far. You can also see my new hardwood Z bar clamps which I forgot to take a close-up of.

Z Motor Bracket
Bottom View

Here's my newest part. Looks like I'll have to touch up that horizontal hole with a hand drill or something, clearly it's not very straight.. For some reason, drilling a straight hole with my pedestal drill is almost impossible.

More Breakage

Section view of
Bearing Collar
Collar In-situ

Here's a section view of the collar I made to put M6 studding in a 608 bearing. Note the lengthwise cut which allows me to reduce the diameter enough for it to fit properly.

Broken Parts

These parts all broke because 6mm holes don't accept 6mm studding too well, especially when they're not particularly straight. Widening them out to 6.35mm (1/4") helps immensely, as does eyeballing them straight rather than relying on the pedestal drill. I filled the cracks with PVA and clamped them for the night. One of them had already split, and it split again on the other side indicating that the glue is stronger than the wood!

Motor Driver Overview
Motor Driver in operation

Quick shot of motor driver operating in its new location with some debug output on the screen.